TJ Lock-N-Load Long-Arm Suspension System, 6 Pak Edition



 
**Featuring Next Gen 6Paks**
**Longer Travel & Easy Install**

The MetalCloak TJ Wrangler Lock-N-Load Long-Arm Suspension 6Pak Edition beats most aftermarket kits in flex, wheel travel and on & off-road drivability. Period.

Driven by Technology including the MetalCloak Patented (US Patent 9,174,504) Lock-N-Load™ Radius Arm, MetalCloak's 6Pak™ Long Travel Shocks, MetalCloak True Dual Rate™ Coils, and Duroflex™ Control Arms with our patent pending Duroflex Bushings, no other off-the shelf Long-Arm kit can compare.

The MetalCloak TJ Wrangler Long-Arm 6Pak Edition achieves maximum articulation with MetalCloak's 6Pak™ Long Travel Shocks.

Note:This Kit Requires Welding at the Rear Axle.

Note: MetalCloak Recommends You Have a Suspension Specialist Align Your Jeep Once MetalCloak Suspension is Installed.

Note: MetalCloak does not recommend powder coating your True Dual Rate Coils. See instructions for additional details.

: $5,329.00

Availability: Usually Ships in 5-7 Days
Product Code: 7142


4.5" Lift or 6" Lift:
  

 
Features Specifications & Materials Installation Instructions
 

Dividing Line

EXCLUSIVE TECHNOLOGY - THIS AIN'T YOUR TYPICAL LONG ARM

Yes, the Radius Arm is back!

Radius Front Control Arms:

  • Fit ideally in to the limited space under the TJ Wrangler.
  • Aid to the protection of vital components of the under carriage.
  • Allow maximum up and down wheel travel while keeping the pinion angle in check.
  • Have unparalleled on-road handling characteristics that cannot be denied.

But Radius Arms typically have a major problem... BIND. This bind causes premature bushing wear and undue stresses on the axle.

But, if we wanted a Radius Arm, we needed a Solution...

Radius Arm
Radius Arms Featuring the Lock-N-Load

Dividing Line

MEET LOCK-N-LOADTM OUR PATENTED SOLUTION FOR RADIUS ARM BIND

The Lock-N-Load solves the problem of the inherent bind of Radius Arm systems.

  • Eliminates Radius Arm Bind
  • Dual-Purpose Control Arm
  • "Lock It" for Daily Driving
  • "Load It" for Trail Articulation
  • Built with Duroflex¯¯™ Joints
  • Exclusive Patented (US Patent 9,174,504) Technology
  • Articulate like a 3-Link, but with the safety of a 4-Link

Watch the video>>>

Lock n Load Video
Standard Tube FEnder Clearance

Learn More about the Lock-N-Load >>>

Dividing Line

DUROFLEX - BRINGING FLEXY BACK

The next step in our evolution of the Radius Arm Suspension is the Duroflex™ Joint (Patent Pending) -- the key to getting the greatest off the shelf flex & on the road ride quality in a TJ/LJ Wrangler suspension kit. Period.

OEM Clevite and Typical Flex Joint is the Duroflex Joint

MetalCloak has taken the best features of the most widely used control arm joints and combine those features to create the Duroflex Joint, producing a Low-Maintenance, High-Misalignment (34˚), Self-Centering, Rebuildable Joint with an OEM quality ride.

OEM Style Clevite Joint Typical Flex Joint MetalCloak Duroflex Joint
  • High Vibration Dampening
  • Self-Centering
  • Fused at Center Bushing
    (No Bearing Surface Wear)
  • High Transverse Flex
  • High Rotational Flex
  • Rebuildable
  • High Vibration Dampening
  • Self-Centering
  • Fused Center Bushing
    (No Bearing Surface Wear)
  • High Transverse Flex
  • High Rotational Flex
  • Rebuildable

Dividing Line

DEGREES OF ARTICULATION...

MetalCloak's Duroflex Joint provides 28˚ more articulation and flex then typical control arms! (video)

Duroflex Control Arms Articulation Low ARticulation Joints.

Dividing Line

OKAY, THAT'S COOL TECH, BUT WHAT ABOUT THE REST?

Oh, we're not done... from the control arms to the belly pan, we thought of (just about) everything.

Duroflex Control Arms Articulation
Lower Front Control Arms

Both the Front Radius Arms and the Lower Rear Hi-Clearance Arms are manufactured for the ultimate in strength and versality.

  • 2" .25 wall 4130 Chromoly DOM
  • Signature Gold Zinc Chromate (video)
  • Oversized Duroflex Joints at the Belly Pan
Made strong and made to last!

Dividing Line

THE 4-LINK REAR, PERFECTED

While the Radius Arm front was ideal, we realized the space in the rear allows for a properly engineered 4-Link.

Choosing the 4-link rear control arm design provides added torque strength support for the main drive axle and provides a fantastic overall ride quality.

Our design eliminated the typical unsteady "Long Arm Roll" felt on a lifted TJ while cornering - and that's without running a rear sway bar!

4 link rear

4 link rear

Lower Arms, Bent for Extreme Clearance

Upper Arms Use Custom Brackets to Mount.

Dividing Line

COIL SPRINGS 101-EVERYTHING YOU NEED TO KNOW ABOUT COIL SPRINGS

This short video covers what you need to know about the basics of Single Linear Rate Coil Springs and MetalCloak's True Dual Rate Coils. How Linear Coil Springs and MetalCloak's True Dual Rate Coils work and what to expect when using them.

Check Out the Video>>>

Coils 101 Video

Dividing Line

WHAT ARE TRUE DUAL RATE ™ COILS?

MetalCloak TJ/LJ Wrangler True Dual Rate™ Coils have some of the longest free lengths in the industry for greater articulation without sacrificing the OEM ride quality.

Understanding Dual Rate Coils

Dividing Line

TRUE DUAL RATE ™ COILS CREATE A "VIRTUAL" BUCKET!

By effectively lowering the bucket on the coil, you get a much more stabile
ride that reduces the potential for buckling.


Stock Clearance Jeep

Learn More about the True Dual Rate™ Coils Specifications >>>

Dividing Line

FULLY INTEGRATED 3 PIECE BELLY PAN

1/4" Plate Steel provides the Ultimate in Strength while providing bolt-on Control Arm Geometry.

  • 1/4" Plate Steel Mounting Points
  • Stiffens Chassis
  • 3 Piece Belly Pan Provides Easy Access to Transmission & Transfer Case
  • Boat-Sided Style 1/4" Steel Plate Angled for Approach & Departure
  • Front & Rear Approach and Departure Ramps Designed to Slide Up & Over the Rocks
  • Stock or Aftermerket Transfer Cases OK
  • Two Versions - Early or Late Model TJ's
Early Belly Pan Late Model Belly Pan

Understanding Dual Rate Coils

Dividing Line

3 PIECE BELLY PAN RIDE HIEGHT

The MetalCloak 3 piece belly pan fits aftermarket transfer cases (*i.e. Atlas) with no floor modifications or body lift. MetalCloak's 3 piece belly pan is as tall as the factory belly pan allowing you to lose no ground clearance.

Early Belly Pan Specs

Dividing Line

Early Belly Pan Specs

Dividing Line

NOT JUST ANY TRACK BAR BUSHING... MEET THE DUROTRAK™
This short video covers what you need to know about the Durotrak Bushing. The Durotrak™ Bushing (Pat Pend #14/622,350) is a bushing made with a proprietary rubber compound unique to MetalCloak. The Durotrak™ bushing is comprised of two pieces that thread together allowing this bushing easy to install without a press. Eliminate squeaks and clunks in your steering with the technology of MetalCloak's Durotrak™ bushings; exclusively found in MetalCloak track bars.

Check Out the Video >>>

Durotrak Bushing Video

Durotrak Bushing

The Durotrak™ Bushing (Pat Pend #14/622,350) is a NVH (noise, vibration, harshness) bushing made with a proprietary rubber compound unique to MetalCloak. The Durotrak™ two part bushing is comprised of two pieces that thread together making this bushing simple to install without a press, reduces vibration and harshness transferred to the driver, and improves vehicle steering input.

Dividing Line

REAR TRACK BAR DESIGNED FOR ULTIMATE STRENGTH & CLEARANCE

Formed for ultimate Up-Travel & Down-Travel we built it out of Solid Chromoly for
strength and equipped it with our patented Duratrak bushing for improved durability and ride stability.
TJ Long Arm Front Track Bar

Dividing Line

SOLID CHROMOLY FRONT TRACK BAR KEEPS YOU... WELL... ON TRACK.

Formed for ultimate Up-Travel & Down-Travel the TJ Wrangler Front Track Bar
gives strength, clearance, ultimate clearance and is equipped with our Patented Duratrak bushing for improved durability and ride stability.
TJ Long Arm Front Track Bar

Dividing Line

MetalCloak 6Pak

MetalCloak's Floating Shock Body Technology (FST) provides a game-changing platform featuring parallel shafts extending from a floating body, centralized by dual opposing reservoirs; this revolutionary feature allows for twice the usual stoke over typical industry shocks.

Now the problems of low-hanging shocks or limited travel because of your shock body are fully and completely eliminated.

The shock is no longer the limiting factor in your build.

Duroflex 101 Video
Duroflex 101 Video

Each 6Pak shock is hand built to exacting standards and then Dyno tested here at MetalCloak in Sacramento California.

Designed specifically for applications where space is paramount; the 6Pak shock body extends shafts from both sides of a floating remote reservoir and allows for a much smaller compressed shock while having up to 14inches of travel!

7043 Exploded View
1200 Cut Away

6 Pak Specs...

Nitrogen Charged:

  • Dual Opposing Reservoris
  • 150psi - 160 psi per side (end user can custom adjust if desired)

Shaft (Rod) Material:

  • Parallel Shafts Extend from a floating body
  • AISI 1045 centerless ground steel shaft, Rockwell hardness C70 hard chrome plated, 12RMS finish

Rod End:

  • Industry Standard rod end (½ inch fine thread) ½ - 20 UNF (multiple types of rod ends and work)
  • Rod Ends feature adjustable length & Teflon Race

Tube Housing:

  • Seamless 6061-T6 aircraft-grade aluminum
  • Piston wearbands are Bronze impregnated Teflon (40% Bronze 60% Teflon)

Shaft Wiper-Seal:

  • Teflon dual wiper & triple seal

Valve Disks (stacks):

  • Butteryfly style 17-7PH stainless steel, with a Rockwell hardness of C40
  • Fully Rebuildable & Tunable

Dividing Line

STOP THE GUESS WORK. BUMP IT UP!

Our Adjustable Bump-Stops remove the guess work on your Jeep and lets you build the
bump stop you need, when you need it.

MetalCloak Adjustable Bump Stop System...

  • Adjust from 1" - 4" Without Removing Coils
  • Perfect Height Regardless of Tire Size
  • Thermoset Rubber Dampens Impact
  • Additional Pads Available on Request

Get Correct Bump-Stop Height Every Time!

  • 4" - Use all 4 sections and longest hardware bolts for maximum bump-stop height
  • 3" - Use all 3 sections and long hardware bolts for maximum bump-stop height
  • 2" - Two sections and medium hardware bolts are used for medium bump-stop height
  • 1" - One section and the short hardware bolts are used for the minimum bump-stop height
JK Sectional Bump-Stops

Learn More about the Adjustable Bump Stops >>>

Dividing Line

BUMP STOP SIZING RECOMMENDATIONS:

TJ Bump Stop Recommendations

Dividing Line

TJ WRANGLER REPLACEMENT BRAKE LINE, 24"

From the Teflon Inner Core, to the Stainless Steel Braid and Poly Safety Coat, the MetalCloak replacement Brake Lines are designed to meet your needs and exceed your expectations.

Longer then typical brake lines of similar lift heights because of our additional clearance and travel.

TJ Wrangler Hi Clearance Front Track Bar
Learn More about the TJ Wrangler Replacement Brake Lines >>>

Dividing Line

Customers who bought this were also interested in...
Keep Calm and Rubicon Mesh Cap Camo Hat Mesh Cap

Dividing Line


Average Customer Review: 5 of 5 Total Reviews: 1 Write a review.

  1 of 2 people found the following review helpful:
 
tj lock n load April 6, 2015
Reviewer: Anonymous Person from Middleville, MI United States  
very nice product easy to install good directions the only issue I had was a couple bolts were missing for the front lower control arms for the skid plate

Was this review helpful to you?