Front Duroflex Weld-On Bracket and Axle Bushing Kit, Jeep TJ/LJ Wrangler
Front Duroflex Weld-On Bracket and Axle Bushing Replacement Kit, Jeep TJ/LJ Wrangler


 
MetalCloak's Duroflex bushings are designed to work in parallel, but what about the axle side?

Factory Clevite bushings will work in conjunction with Duroflex bushings. Factory Clevites are a self centering rubber bushing, however, they have a very limited range of performance.

To optimize the Duroflex joints in your MetalCloak control arms and fully benefit with:
  • Increased dampening of NVH (noise/vibration/harshness)
  • Articulation (34 degrees)
  • Rotation (360 degrees)
Upgrade the Clevites to Duroflex Axle-Side Bushings! With this weld-on system you will upgrade your bushings along with strengthening the weak stock tower-housing with the New MetalCloak Front Duroflex Weld-On Bracket and Axle Bushing Kit!

MetalCloak's Front Duroflex Weld-On Bracket and Axle Bushing Kit ONLY works with MetalCloak's Duroflex Control Arms.

The Front Duroflex Weld-On Axle Bushing Kit comes complete with a press-in Duroflex bushing for the cast side and a reinforced weld-on bracket to contain the Duroflex Bushing on the other side.

Note: MetalCloak's Front Duroflex Weld-On Bracket and Axle Bushing Kit ONLY works with MetalCloak's Duroflex Control Arms. MetalCloak's Front Duroflex Weld-On Bracket and Axle Bushing Kit is not recommended for any other control arms.

: $99.00

Availability: Usually Ships in 1 to 2 Weeks
Product Code: 7349

Features Specifications & Materials Installation Instructions
 
FRONT DUROFLEX WELD-ON BRACKET AND AXLE BUSHING KIT

The included billet tower reinforcement and 11GA steel plated gusset welds to the axle provides additional strength over the factory bracket. Get the unparalleled ride performance and increased strength with the MetalCloak Front Duroflex Weld-On Axle Bushing Kit.

Standard Tube FEnder Clearance
Dividing Line
Duroflex bushings provide the best vibration dampening (NVH) anywhere, along with more self-centering misalignment than any other bushing available.

MetalCloak's Front Duroflex Weld-On Bracket and Axle Bushing Kit ONLY works with MetalCloak's Steel and Aluminum Duroflex Control Arms.
Driver Side Bushing Passenger Side Bushing
Dividing Line

DUROFLEX 101-EVERYTHING YOU NEED TO KNOW ABOUT THE DUROFLEX JOINT

This short video covers everything you need to know about the basics of the MetalCloak Duroflex Joint.

Check Out the Video>>>

Dividing Line
THE DUROFLEX JOINT PROVIDES THE BEST RIDE. PERIOD.

High Vibration Dampening & Self Centering...

Made of a Proprietary Rubber Compound, the High Vibration Dampening and Self-Centering characteristics of the Duroflex Joint means you will always get...

  • The best ride quality
  • No binding of your control arms.
  • None of the micro-wear that DESTROYS Flex Joints

Standard Tube FEnder Clearance
Standard Tube FEnder Clearance

High Misalignment...

By adapting the High Transverse Flex characteristics of a typical Flex Joint, the Duroflex Joint gives you...

  • Over 34 of Misalignment
  • Over 68 per Control Arm

Absorbs Micro-Movements...

Because the Duroflex Bushing absorbs the millions of Rotational Micro-Movements found in your daily driving, you get...

  • Improved Ride Quality
  • None of the micro-wear that DESTROYS Flex Joints
Standard Tube FEnder Clearance
Standard Tube FEnder Clearance

True Bearing Surface...

The outer surface of the Duroflex Bushing acts as a bearing, breaking free when called for, giving you...

  • Maximum Rotation & Articulation
  • No "Binding Up" of the Control Arms

Low Maintenance & Rebuildable...

Unlike typical Flex Joints, the Duroflex does not require replacing key parts every year like others...

But, when you do need to rebuild it, it is MetalCloak Easy!

Just pull out the Duroflex Bushing, clean it up, add some new Teflon impregnated, synthetic silicone grease. Reassemble.

Done.

Standard Tube FEnder Clearance
Dividing Line

Q: WHAT IF A CLEVITE JOINT MET A FLEX JOINT IN A BAR...

A: You'd have the key to the MetalCloak Control Arms, the Patent Pending Duroflex TM Joint (metalcloakpatents.com).
Standard Tube FEnder Clearance

Metalcloak has taken the best features of the most widely used control arm joints and combined those features to create the Duroflex Joint, producing a Low-Maintenance, High-Misalignment (34), Self-Centering, Rebuildable Joint with an OEM quality ride.

OEM Style Clevite Joint Typical Flex Joint MetalCloak Duroflex Joint
  • High Vibration Dampening
  • Self-Centering
  • Fused at Center Bushing
    (No Bearing Surface Wear)
  • High Transverse Flex
  • High Rotational Flex
  • Rebuildable
  • High Vibration Dampening
  • Self-Centering
  • Fused Center Bushing
    (No Bearing Surface Wear)
  • High Transverse Flex
  • High Rotational Flex
  • Rebuildable
Dividing Line
TESTIMONIALS & BUZZ:
Check out what Jeepers everywhere are saying about our products on The Buzz Page.
Dividing Line
Customers who bought this were also interested in...
Keep Calm and Rubicon Camo Hat Mesh Cap
Dividing Line

Average Customer Review: 5 of 5 Total Reviews: 1 Write a review.

  0 of 0 people found the following review helpful:
 
Easy September 6, 2018
Reviewer: Matt (K0KB) from Maquoketa, IA United States  
Easy to install and you can not beat the duroflex bushings!

Was this review helpful to you?